Skip to content

Free roof inspection that checks the small stuff too: (317) 743-3417

Cumberland · Lawrence · New Palestine · Greenfield

(317) 743-3417
Roofer in a yellow safety harness kneeling on underlayment, drilling a dark standing-seam metal panel on a house roof, with spare panels and a ladder at the eave

ServicesMetal Roofing

Metal Roofing in Cumberland, IN

A metal roof can last for decades, but only if the small parts are done right. We fasten panels so they can move with the heat, bend trim to fit your home, and seal every spot where water tries to sneak in.

A long-lasting roof, if it goes on right

The panels on a metal roof rarely wear out first. The trouble starts at the edges, the seams and the screws. Screw a panel down too tight and it can't move when the sun heats it. Flash a chimney with caulk instead of bent metal and it starts leaking within a few winters. Those are the spots where we slow down.

We put on standing seam and exposed-fastener panels for homes in Cumberland and nearby towns like Greenfield, New Palestine and Fortville. Our crew is licensed, bonded and insured, and we pull the permit when your town calls for one.

If metal doesn't suit your home or your budget, we'll tell you. Then we'll walk you through shingle roofing or a roof replacement with a different material.

Roofer in a yellow safety harness drives a screw into a charcoal standing-seam metal panel at the eave of a house, with a neighboring home and lawn behind.

What goes into a metal roof we install

  1. 01

    Tear-off and deck check

    We take the old roof down to the wood. Soft or rotted sheathing gets replaced, and we show you photos of what we found before we cover it up.

  2. 02

    High-heat underlayment and ice barrier

    Metal gets hot in summer, so we use a synthetic underlayment rated for it. Ice and water shield goes along the eaves, in the valleys and around pipes and chimneys, where winter ice backs up first.

  3. 03

    Panels fastened to move

    On standing seam roofs, hidden clips hold the panels while letting them expand and contract. On exposed-fastener roofs, each screw is driven snug so the rubber washer seals without getting crushed. Overdriven screws are the most common leak we see on older metal roofs.

  4. 04

    Trim and flashing bent on site

    We bend drip edge, gable trim, sidewall flashing and chimney counterflashing on a brake right at your home. Every piece is lapped so water runs over it, not behind it.

  5. 05

    Vented ridge with closures

    Foam closures under the ridge cap keep out wind-driven snow, rain and wasps while still letting the attic breathe.

  6. 06

    Cleanup that protects the finish

    Drilling and cutting leave metal shavings. We brush them off the panels the same day so they don't rust and stain the paint, then run a magnet over the yard and driveway for screws.

Questions about Metal Roofing?

Call(317) 743-3417

Signs metal roofing might be the right call

  • Your shingles are near the end

    If your shingle roof is curling or losing granules and you plan to stay in your home a long time, metal is worth pricing out. It costs more up front but can outlast more than one shingle roof.

  • Your old metal roof leaks at the screws

    Rubber washers dry out and crack over time. Drips in a straight line, or water stains under the screw rows, usually point there.

  • Rust streaks or loose panels

    Rust running down from fasteners or trim, or panels that rattle in the wind, means the roof needs repair or new panels before the deck gets wet.

  • Ice dams every winter

    Snow and ice slide off metal much more easily than off shingles. Paired with good ventilation, that can cut down on the ice buildup at your eaves.

How a metal roof job goes

  1. 1

    Free roof inspection

    We walk the roof itself, look at the underside of the decking from your attic when there's access, and check the flashing, vents and gutters. You get photos and a straight answer on whether metal makes sense.

  2. 2

    Written estimate and choices

    We go over panel style, gauge and color, plus snow guards if you want them. The estimate is written out line by line so you can see what you're paying for.

  3. 3

    Tear-off and prep

    We cover landscaping and protect the walls and windows, then strip the old roof and fix the deck. Underlayment and ice barrier go down the same day so your home stays dry.

  4. 4

    Panels and trim

    Panels are measured and cut with shears, not grinders, so hot filings don't burn the paint. Trim and flashing go on as we work up the roof.

  5. 5

    Final walk-through

    We check every seam, screw line and flashing joint, clean up, and walk the property with you before we call it done.

What sets the cost of your metal roof

We build each estimate from your home's measurements and what we find on the roof, not from a chart. After the free inspection you get a written estimate with each item on its own line. Financing is available if you'd rather spread the cost out.

Panel system
Standing seam with hidden clips takes more labor and material than exposed-fastener panels. The gauge of the steel and the paint finish move the number too.
Roof shape
Valleys, dormers, skylights and chimneys each need trim and flashing bent to fit. A simple two-slope roof with one ridge takes far fewer hours than one broken up by angles and openings.
What's under the old roof
How many layers come off and how much sheathing has to be replaced both change the total. You see photos of the deck before any added work goes on the estimate.
Extras and permits
Snow guards, new gutters, more attic ventilation and permit fees can all be part of the job. Each one gets its own line so nothing is buried.

Metal roof questions we hear most

Is a metal roof loud when it rains?

Not on a house. The solid wood deck and underlayment under the panels absorb most of the sound, so a storm sounds about like it does with shingles. The drumming people expect comes from barns and sheds with open framing and no deck.

Can metal go right over my old shingles?

Some places allow it, but we usually advise against it. Tearing off lets us find and replace rotten decking and put down a real ice barrier. Covering old shingles hides problems that cost you more down the road.

Does hail dent metal panels?

Big hail can dent metal, more so on thinner panels. Those dents are mostly about looks and rarely lead to leaks the way cracked shingles do. If hail is a concern for you, we can go over heavier gauge panels.

How many days does the install take?

Most homes take several days, depending on size and how many angles and openings the roof has. Standing seam takes longer than exposed-fastener panels. We keep the roof covered every night, so weather between work days isn't a problem.

How do I choose between metal and shingles?

It comes down to how long you plan to stay and what you want to spend. As an Owens Corning Preferred Contractor we put on shingle roofs too, so we have no reason to steer you one way. After the inspection we'll lay out the trade-offs for your home.

Elevated view of a charcoal asphalt shingle roof with hip ridges, a valley, roof vents and a pipe vent, an aluminum ladder at the gutter, and a tree-lined street behind

Let's look at your roof first

We'll check the roof, the deck and the flashing, then tell you plainly whether metal fits your home. No cost for the visit.